Page Count: Introduction 1. Control Elements and Connectors 2. Installation 3. U ser Manual.
|Genre:||Health and Food|
|Published (Last):||2 March 2007|
|PDF File Size:||6.40 Mb|
|ePub File Size:||15.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
Table of Contents Important Safety Instructions Control Elements and Connectors Important Safety 9. Box , to constitute risk of electric shock. Allother This symbol, wherever it appears, Refer all servicing to qualified service personnel. Please read the manual. Servicing is required when the apparatus has been operating conditions for a period of one 1 year from Caution damaged in any way, such as power supply cord or plug the original date of purchase see the Limited Warranty To reduce the risk of electric shock, donot is damaged, liquid has been spilled or objects have fallen terms in 4 below , unless a longer minimum warranty remove the top cover or the rear section.
If the product No user serviceable parts inside. Refer servicing to to rain or moisture, does not operate normally, or has shows any defects within the specified warranty period qualified personnel. The apparatus shall be connected to a MAINS socket using suitable new or reconditioned product or parts.
To reduce the risk of fire or electric shock, outlet with a protective earthing connection. Where the MAINS plug or an appliance coupler is thislimited warranty shall apply to the replacement moisture. The apparatus shall not be exposed to dripping used as the disconnect device, the disconnect device shall product for the remaining initial warranty period, i. Caution 3 Upon validation of the warranty claim, the repaired These service instructions are for use or replacement product will be returned to the user by qualified service personnel only.
Toreduce the risk of electric shock do not perform any 4 Warranty claims other than those indicated above servicing other than that contained in the operation are expressly excluded. Repairs have to be performed by qualified servicepersonnel. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Registeringyour 7. Do not block any ventilation openings. Support at behringer. Ifyour country is not connection or operation of the unit in any way 3 This warranty does not detract from the sellers listed, please check if your problem can be dealt with that does not comply with the technical or safety obligations in regard to any lack of conformity of the by our OnlineSupport which may also be found under regulations applicable in the country where the product and any hidden defect.
Alternatively,please submit product is used; an online warranty claim at behringer. All inquiries must be accompanied accident, fire, flood, etc or any other condition that Warranty service conditions are subject to change without by a description of the problem and the serial number is beyond the control of MUSICGroup. For the latest warranty terms and conditions of the product. Afterverifying the products warranty and additional information regarding MUSICGroups 7 Any repair or opening of the unit carried out by eligibility with the original sales receipt, MUSICGroup limited warranty, please see complete details online at unauthorized personnel user included will void the will then issue a ReturnMaterials Authorization behringer.
RMA number. If the buyer fails to submit a written repair order within 6 weeks after 1 This limited warranty does not cover consumable notification, MUSICGroup will return the unit C. Such costs will Where applicable, MUSICGroup warrants the valves or also be invoiced separately when the buyer has sent in a meters contained in the product to be free from defects written repair order.
Purchasesmade 2 This limited warranty does not cover the product through an online auction are on a buyer beware basis. If the product needs to be modified or accepted for warranty verification and MUSICGroup will adapted in order to comply with applicable technical not repair or replace any product purchased through an or safety standards on a national or local level, inany online auction.
No other person reseller,etc. It does not cover technical assistance for Subject only to the operation of mandatory applicable hardware or software usage and it does not cover local laws, MUSICGroup shall have no liability to the buyer any software products whether or not contained in under this warranty for any consequential or indirect the product. Any such software is provided AS IS loss or damage of any kind.
In no event shall the liability unless expressly provided for in any enclosed software of MUSICGroup under this limited warranty exceed the limitedwarranty. It supersedes are expressly excluded from this limited warranty, all other written or oral communications related to this inparticular, if caused by improper handling of the product. This also applies to defects caused this product. Introduction The block diagram supplied with the mixing console gives you an overview of the connections between the inputs and outputs, as well Congratulations!
For the moment, just try and trace the signal path from the microphone input to the FX send connector. If you look at the overview of the controls at the same phantom power supply , line inputs, possibilities for connecting effects devices, time, youll be able to quickly familiarize yourself with your mixing console and connectors for a 2-track master machine e. DAT recorder and a monitor system youll soon be making the most of all its many possibilities. Nevertheless, we recommend that you carefully examine the The extremely low-noise and distortionfree circuitry guarantees absolutely packaging and its contents for any signs of physical damage, which may have natural and transparent signal reproduction occurred during transit.
The console meets the required safety standards. Always be careful to Blownfuses must only be replaced by fuses of the same type and rating.
First connect the power supply unit to the Important notes concerning installation console, then connect the power supply unit to the mains. The sound quality may diminish within the range of powerful Please note that all units must be properly grounded.
For your own broadcasting stations and high-frequency sources. Increase the safety, you should never remove any ground connectors from electrical distance between the transmitter and the device and use shielded devices or power cables, or render them inoperative.
Please ensure that only qualified people install and operate the 1. During installation and operation, the user must have sufficient electrical contact to earth, otherwise electrostatic discharges A mixing console fulfils three main functions: might affect the operation of the unit.
Signal processing: Preamplification, level adjustment, mixing of effects, frequency equalization 1. Mix: Setting the volume level, frequency distribution and positioning of the Should your BEHRINGER product malfunction, it is our intention to have it individual signals in the stereo field, level control of the total mix to match repaired as quickly as possible.
Should your country not be listed, please contact the distributor nearest you. A list of distributors can be found in the support area of our website 1. The users manual is designed to give you both an overview of the controls, Registering your purchase and equipment with us helps us process your repair aswell as detailed information on how to use them.
In order to help you claims more quickly and efficiently. The illustrations at the beginning of each chapter Thank you for your cooperation! Control Elements and Connectors EQ This chapter describes the various control elements of your mixing console. The upper HI and the lower band LO are shelving filters that increase or Allcontrols, switches and connectors will be discussed in detail.
The cut-off frequencies of the upper and lower band are 12 kHz and 80 Hz respectively. Please also note the instructions in chapter 2. The bus appears at the consoles FX send output and can be fed from there to an external effects device.
Unbalanced devices mono jacks can also be connected to these inputs. As the name suggests, the FX sends of the EURORACK mixing consoles are Please remember that you can only use either the microphone intended to drive effects devices reverb, delay, etc and are therefore configured or the line input of a channel at any one time.
You can never use post-fader. This means that the mix between dry signal and effect remains at bothsimultaneously! If this were not the case, the effects signal of the channel would remain GAIN audible even when the fader is lowered to zero. Use the GAIN control to adjust the input gain. This control should always be turned fully counterclockwise whenever you connect or disconnect a signal PAN source to one of the inputs.
The PAN control determines the position of the channel signal within the stereo image. This control features a constant-power characteristic, which means the 2. All bands provide boost or cut of up to 15 dB.
In the central position, the equalizer is inactive. If a channel is operated in mono via the left line input, this control has the same function as the PAN control used in the mono channels. At dBV home-recording right channels. The stereo channels are designed to handle typical line level signals. Both inputs will also accept unbalanced jacks. Thefilter characteristics and cut-off frequencies are the same as those in the mono channels.
A stereo EQ is highly preferable to two mono equalizers. You can instead use these connectors as additional inputs, but any effects device will then have to be brought back into the console via a normal stereo channel.
This does, however, give you the ability to use the channel EQ on the effects return signal if you wish. When using a stereo channel as effects return path, the FX control of the relevant channel should generally be turned fully down to avoid undesirable feedback. The post-fader FX signal you created using the input channels. Use the taken from the stereo input before it is sent to the FX bus. UB only. The UB is not equipped with control room outputs.
This will avoid the control for this purpose. They can also be used as a standard stereo line do not feature this switch. The illustrations activates the phantom power supply on the XLR connectors of all mono channels. Be sure to use only high-gradecables. Connect the micro-phones before you switch on the You can, of course, also connect unbalanced devices to the balanced power supply.
To do this, use either mono plugs or stereo plugs with the ring muted before you activate the phantom power supply. After switching and sleeve bridged pins 1 and 3 in the case of XLR connectors.
Behringer Audio Mixer UB1202/UB1002 User Manual
Behringer EURORACK UB1202 User Manual