LM170E01 PDF

Shipping time : 2 - 4 workdays. Pictures may differ from the original. Available now! Add to basket. Wishlist Compare.

Author:Yogor Mezibar
Country:French Guiana
Language:English (Spanish)
Genre:Love
Published (Last):27 March 2006
Pages:398
PDF File Size:3.89 Mb
ePub File Size:12.67 Mb
ISBN:865-8-36754-313-4
Downloads:72829
Price:Free* [*Free Regsitration Required]
Uploader:Brataur



Philips LCD Co. Product Engineering Dept. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than The LMETLB3 is intended to support applications where thin thickness,wide viewing angle, low power are critical factors and graphic displays are important.

In combination with the vertical arrangement of the sub-pixels, the LMETLB3 characteristics provide an excellent flat panel display for office automation products such as monitors.

RGB stripe arrangement Transmissive mode, normally white Hard coating 3H , Anti-glare treatment of the front polarizer Feb. Absolute maximum ratings The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. Table 1. Temperature and relative humidity range are shown in the figure below. Temperature and relative humidity Ver 0. Electrical specifications Another which powers the CCFL, is typically generated by an inverter. The inverter is an external unit to the LCD.

Table 2. The design of the inverter must have specifications for the lamp in LCD Assembly. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter no lighting,flicker,etc never occurs. When you confirm it,the LCD Assembly should be operated in the same condition as installed in your instrument.

Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape, TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage current occurs between lamp wire and conducting tape.

The duration of rush current is about 5ms. The voltage above VBS should be applied to the lamps for more than 1 second for start-up. Otherwise,the lamps may not be turned on. Ver 0. The output of the inverter must have symmetrical negative and positive voltage waveform and symmetrical current waveform. Lamp frequency may produce interference with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away as possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference.

The used lamp current is the lamp typical current. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its leakage current. The ideal sine wave form shall be symmetric in positive and negative polarities. Inverter open voltage must be more than lamp starting voltage.

The inverter which is combined with this LCM, is highly recommended to connect coupling ballast condenser at the high voltage output side. When you use the inverter which has not coupling ballast condenser, it may cause abnormal lamp lighting because of biased mercury as time goes.

This LCD employs a interface connection, a 30 pin connector is used for the module electronics interface. Four 2pin connectors are used for the integral backlight system. The pin configuration for the connector is shown in the table 3 and the signal mapping with LVDS transmitter is shown in the table 4. Table 3. Module connector pin configuration Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Ver 0.

Power supply 5. All VCC power input pins should be connected together. All NC pins should be separated from other signal or power.

The pin configuration for the connector is shown in the table 5. Table 5. The high voltage side terminal is colored white or pink. The low voltage side terminal is white or Blue. The backlight ground should be common with LCD metal frame.

Table 6. No variation of the total number of Hsync and DE in a frame is required for normal operation. No variation of the total number of clock in a Hsync period for tVBP is required for normal operation. Color Input Data Reference The brightness of each primary color red,green and blue is based on the 8-bit gray scale data input for the color ; the higher the binary input, the brighter the color.

The table below provides a reference for color versus data input. Table 7. Please avoid floating state of interface signal at invalid period.

Lamp power must be turn on after power supply for LCD and interface signals are valid. Surface luminance is the center point across the LCD surface 50cm from the surface with all pixels displaying white.

For more information see [ Figure 10 ]. For additional information see [ Figure 11 ]. Viewing angle is the angle at which the contrast ratio is greater than The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see Figure Gray scale specification Table Mechanical Characteristics Table Please refer to Figure 15,16 regarding the detailed mechanical drawing of the LCD.

Table Front view Ver 0. Rear view Ver 0. Reliability Table Environment test condition No. International Standards Packing The label is attached to the backside of the LCD module. This is subject to change without prior notice. Mounting Precautions 1 You must mount a module using holes arranged in four corners or four sides. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module.

Transparent protective plate should have sufficient strength in order to the resist external force. And please do not rub with dust clothes with chemical treatment.

Do not touch the surface of polarizer for bare hand or greasy cloth. Some cosmetics are determined to the polarizer. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. Their long time contact with polarizer causes deformations and color fading. Operating Precautions 1 The spike noise causes the mis-operation of circuits.

In lower temperature, it becomes longer. In lower temperature, it becomes lower. And in lower temperature, response time required time that brightness is stable after turned on becomes longer. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.

Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference. Otherwise, LCM can not be operated its full characteristics perfectly.

Electrostatic Discharge Control Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. Precautions for Strong Light Exposure Strong light exposure causes degradation of polarizer and color filter. Storage When storing modules as spares for a long time, the following precautions are necessary.

Do not expose the module to sunlight or fluorescent light. It is recommended that they be stored in the container in which they were shipped.

ANASTASIA VLADIMIR MEGRE PDF

LM170E01 Datasheet

Please enter the product you want to resell number, quantity, packaging, product location, etc. Please enter your message and kindly provide your contact information. We will contact you as soon as possible. Please enter your inquiry qty or any information you need, and kindly provide your contact information.

IKATAN PENGAKAP PDF

Datasheets search archive of electronic components datasheets

.

Related Articles